Order $24.50 or more to qualify for FREE Shipping on eligible items. (Contiguous 48)

Floortek 6 NanoCoat formerly TK6™ NanoCoat Concrete Sealer


About

TK6™ NanoCoat from Richard James Specialty Chemical Corp. is a very durable, single component, nano-based copolymer that offers the same scratch and chemical resistance as urethane without the need to blend A and B components. The waterborne formula is low odor and suitable for use everywhere — even Southern California. 

TK6 concrete and stone sealer is easy to apply and creates a durable shell that protects against stains while offering great abrasion resistance. Its Nanotechnology formulation penetrates deep inside concrete and delivers great stain protection in both a gloss or extra low gloss finish.

TK6 performs with equal excellence over alkaline and acidic substrates, solving two major problems of finished concrete floors: ASR and incomplete acid neutralization.

TK6 is UV stable for exterior and interior use, for use over both tight and open surfaces. It is very fast dry for job-site efficiency, water submersible with early water resistance, low odor, and offers excellent blush resistance. It is VOC compliant, and both a color carrier and colorable sealer.

When totally cured, TK6 meets the performance characteristics of FDA 4-101.11 for food contact surfaces.

Specs

Available in Gloss and XTRA Low Gloss, 32 oz bottles, 1 gallon bottles, and 5-gallon pails. 

Application is with pump-up sprayer plus microfiber pad, or HVLP, roller or squeegee. 

Use RJSC top-coat or two coats for concrete, first often 30% water-diluted. Burnish with 400-grit diamond-embedded pads on low speed machine for top performance. 

Coverage: ~250 – ~1000 sq.ft./gal/coat, substrate dependent. 

Apply at 60ºF - 85ºF ambient and substrate temperature. Low humidity and good air flow are important.

  • VOC Content: 95 g/L
  • Traffic bearing: 10 hours
  • Re-coat Time: 2-24 hours
  • Gasoline 12 hour test: No Effect
  • Motor Oil 12 hour test: No Effect

Instructions

Before you start:

  • All concrete surfaces should be free of: pooled water, dust, oils, dirt, salts, other finishes and residues.
  • Alkalinity should be between 7 - 8pH.
  • Temperature greater than 60°F and lower than 85°F.
  • Residues from curing compounds, sealers and acid salts may deteriorate under the sealer and release from the substrate after sealing.
  • Do not use prep cleaners containing soy or d-Limonene as these interfere with adhesion of water-borne coatings. If acid treatments are used, neutralize with an ammonia solution (See separate instructions).
  • Do not apply over concrete treated with hardeners or densifiers. (many hardeners contain components that reject/repel waterborne products).


Seal with TK6™ NanoCoat Sealer:

  1. Apply after the final polish with a 400 to 800 grit polishing pad.
  2. The preferred application method is a pump-sprayer and microfiber pads. Dampen the pad before starting.
  3. Apply a liberal spray of TK6™ and immediately spread using a wide microfiber pad. Use smaller pads for corners and edges.
  4. Work fast spreading with a free hand, in arcs or swirls and not in straight lines. For tight substrates, dilute the TK6™ by slowly adding up to 30% water.
  5. Alternatively you can also use an HVLP or airless sprayer with 50-70% overlap.
  6. A single coat will often result in partial protection of the surface due to differential absorbency, so a 2nd application is recommended when the 1st coat is print free (typically less than 3 hours).


Burnishing:

  • TK6 can be burnished after application to “adjust” the final appearance.
  • Burnish with a with a slow-speed polisher, using a high grit diamond embedded Hurricane Burnishing Pads to bring up a higher gloss.
  • For Extra Low Gloss a quick pass with one of the low grit Hurricane Burnishing Pads is recommended.


See More

Floortek 6 NanoCoat formerly TK6™ NanoCoat Concrete Sealer

Quantity must be 1 or more
Regular price
$49.95
Sale price
$49.95

Floortek 6 NanoCoat (formerly TK6 NanoCoat) is ideal for concrete floors, walls, countertops, brick, stone, pavers, stucco, micro-toppings, and self-leveling cements. It's easy to use, provides a beautiful finish, and is a favorite of professional painters, coating applicators, and DIYs. 

  • Easy to use
  • Apply with roller, sprayer, or microfiber cloth
  • Food safe per FDA 4-101.11
  • Great for interior and exterior use
  • Low VOCs and low odor

About

TK6™ NanoCoat from Richard James Specialty Chemical Corp. is a very durable, single component, nano-based copolymer that offers the same scratch and chemical resistance as urethane without the need to blend A and B components. The waterborne formula is low odor and suitable for use everywhere — even Southern California. 

TK6 concrete and stone sealer is easy to apply and creates a durable shell that protects against stains while offering great abrasion resistance. Its Nanotechnology formulation penetrates deep inside concrete and delivers great stain protection in both a gloss or extra low gloss finish.

TK6 performs with equal excellence over alkaline and acidic substrates, solving two major problems of finished concrete floors: ASR and incomplete acid neutralization.

TK6 is UV stable for exterior and interior use, for use over both tight and open surfaces. It is very fast dry for job-site efficiency, water submersible with early water resistance, low odor, and offers excellent blush resistance. It is VOC compliant, and both a color carrier and colorable sealer.

When totally cured, TK6 meets the performance characteristics of FDA 4-101.11 for food contact surfaces.

Specs

Available in Gloss and XTRA Low Gloss, 32 oz bottles, 1 gallon bottles, and 5-gallon pails. 

Application is with pump-up sprayer plus microfiber pad, or HVLP, roller or squeegee. 

Use RJSC top-coat or two coats for concrete, first often 30% water-diluted. Burnish with 400-grit diamond-embedded pads on low speed machine for top performance. 

Coverage: ~250 – ~1000 sq.ft./gal/coat, substrate dependent. 

Apply at 60ºF - 85ºF ambient and substrate temperature. Low humidity and good air flow are important.

  • VOC Content: 95 g/L
  • Traffic bearing: 10 hours
  • Re-coat Time: 2-24 hours
  • Gasoline 12 hour test: No Effect
  • Motor Oil 12 hour test: No Effect

Instructions

Before you start:

  • All concrete surfaces should be free of: pooled water, dust, oils, dirt, salts, other finishes and residues.
  • Alkalinity should be between 7 - 8pH.
  • Temperature greater than 60°F and lower than 85°F.
  • Residues from curing compounds, sealers and acid salts may deteriorate under the sealer and release from the substrate after sealing.
  • Do not use prep cleaners containing soy or d-Limonene as these interfere with adhesion of water-borne coatings. If acid treatments are used, neutralize with an ammonia solution (See separate instructions).
  • Do not apply over concrete treated with hardeners or densifiers. (many hardeners contain components that reject/repel waterborne products).


Seal with TK6™ NanoCoat Sealer:

  1. Apply after the final polish with a 400 to 800 grit polishing pad.
  2. The preferred application method is a pump-sprayer and microfiber pads. Dampen the pad before starting.
  3. Apply a liberal spray of TK6™ and immediately spread using a wide microfiber pad. Use smaller pads for corners and edges.
  4. Work fast spreading with a free hand, in arcs or swirls and not in straight lines. For tight substrates, dilute the TK6™ by slowly adding up to 30% water.
  5. Alternatively you can also use an HVLP or airless sprayer with 50-70% overlap.
  6. A single coat will often result in partial protection of the surface due to differential absorbency, so a 2nd application is recommended when the 1st coat is print free (typically less than 3 hours).


Burnishing:

  • TK6 can be burnished after application to “adjust” the final appearance.
  • Burnish with a with a slow-speed polisher, using a high grit diamond embedded Hurricane Burnishing Pads to bring up a higher gloss.
  • For Extra Low Gloss a quick pass with one of the low grit Hurricane Burnishing Pads is recommended.