Order $24.50 or more to qualify for FREE Shipping on eligible items.

SURFRIDER Wave Sink Mold


About

SURFRIDER Wave Sink Mold contains durable fiberglass construction that allows the mold to be reused time and time again. This fiberglass mold is internally reinforced to avoid any flex from the weight of your concrete.

Specs

  • Length: 20 3/8"
  • Width: 12 7/8"
  • Height: 5 3/4"

Instructions

Concrete Mold Set Up

  • Screws can be used as an option for securing your mold to your casting surface, if casting on melamine. Please note.. make sure you screw through the rimlock and not into the mold. Or use silicone if casting on steel or composite casting deck.
  • Apply a bead/gasket around the perimeter of your sink mold. This can be done with 100% silicone or plasticine clay.
  • Use 2 1/2" drywall screw with a washer or silicone to mount the rubber drain plug to the mold. If you use a drywall screw, pre-drill the mold with a 1/8" drill bit.
  • Apply a coat of tested concrete countertop release agent to the entire mold (inside and outside)


Concrete Sink Removal

  • Using blocks of wood and 2x4's, create a bridge over the concrete sink mold. Position pipe clamps on the bottom of the rim and the top of the 2x4. Clamps should be placed in the furthest outer corners of the mold. Use at least 4 clamps whenever possible. All molds should pop out easily. If it doesn't pop easily, there is likely to be an issue with the application of release or prior contamination of the mold surface.
  • If your mold has not popped out with a firmer tightening of the clamps, inject compressed air around the perimeter of the mold or use a hammer and block to tap around the perimeter of the mold with clamp pressure.
  • Another option is to put ice inside your mold for 30-45 minutes, this will shrink the mold just enough allowing it to break free.


Mold Clean Up

  • Clean your mold with soap and water immediately after each use.
  • Waxing the mold after cleaning is recommended to protect the mold until its next use.
  • Sanding your mold will cause staining of your concrete. Machined buffing compound should be used to reseal the gelcoat surface.
See More

SURFRIDER Wave Sink Mold

Provides an elegant, undulating "wave-like" shape to your integral concrete sink project featuring an eased left and right edge.

Made to order item. Please allow 2-3 business days to ship.

  • Reinforces sink mold, eliminates flex
  • Prevents chipped edges
  • Provides a clamp hold for easy pop out
  • Allows concrete vibration if necessary
Quantity must be 1 or more

Regular price
$255.00
Sale price
$255.00

Provides an elegant, undulating "wave-like" shape to your integral concrete sink project featuring an eased left and right edge.

Made to order item. Please allow 2-3 business days to ship.

  • Reinforces sink mold, eliminates flex
  • Prevents chipped edges
  • Provides a clamp hold for easy pop out
  • Allows concrete vibration if necessary

About

SURFRIDER Wave Sink Mold contains durable fiberglass construction that allows the mold to be reused time and time again. This fiberglass mold is internally reinforced to avoid any flex from the weight of your concrete.

Specs

  • Length: 20 3/8"
  • Width: 12 7/8"
  • Height: 5 3/4"

Instructions

Concrete Mold Set Up

  • Screws can be used as an option for securing your mold to your casting surface, if casting on melamine. Please note.. make sure you screw through the rimlock and not into the mold. Or use silicone if casting on steel or composite casting deck.
  • Apply a bead/gasket around the perimeter of your sink mold. This can be done with 100% silicone or plasticine clay.
  • Use 2 1/2" drywall screw with a washer or silicone to mount the rubber drain plug to the mold. If you use a drywall screw, pre-drill the mold with a 1/8" drill bit.
  • Apply a coat of tested concrete countertop release agent to the entire mold (inside and outside)


Concrete Sink Removal

  • Using blocks of wood and 2x4's, create a bridge over the concrete sink mold. Position pipe clamps on the bottom of the rim and the top of the 2x4. Clamps should be placed in the furthest outer corners of the mold. Use at least 4 clamps whenever possible. All molds should pop out easily. If it doesn't pop easily, there is likely to be an issue with the application of release or prior contamination of the mold surface.
  • If your mold has not popped out with a firmer tightening of the clamps, inject compressed air around the perimeter of the mold or use a hammer and block to tap around the perimeter of the mold with clamp pressure.
  • Another option is to put ice inside your mold for 30-45 minutes, this will shrink the mold just enough allowing it to break free.


Mold Clean Up

  • Clean your mold with soap and water immediately after each use.
  • Waxing the mold after cleaning is recommended to protect the mold until its next use.
  • Sanding your mold will cause staining of your concrete. Machined buffing compound should be used to reseal the gelcoat surface.