Order $24.50 or more to qualify for FREE Shipping on eligible items.

TK Products Bright Seal WB Premium Acrylic Concrete Sealer


About

TK-BRIGHT SEAL WB is an acrylic, waterborne, high solids sealer for new or existing decorative concrete. TK-BRIGHT SEAL WB brings out the “wet look” and highlights the natural pigments in the surface, all while protecting it against abrasion and damage.

TK Bright Seal WB is suitable for interior or exterior use on concrete floors, walls, columns, pavers, burnished block or exposed aggregate. Ideal for use in industrial, commercial, residential or institutional environments. 


Specs

  • Coverage: 300-500 sq.ft/gal
  • Color: Clear
  • VOC: <100 g/L
  • VOC Compliance: AIM, OTC, LADCO, CARB, CSAQMD, Canada
  • Package Qty: 1 gallon plastic bottle

Instructions

PREPARATION
TK BRIGHT SEAL WB is ready for use. Do not dilute. Surfaces must be clean, dry and free of foreign contaminants. Sweep or vacuum to remove dirt or dust, or use Surecrete SCR to clean the surface of oils, grease, stains, wax or polish. Curing compounds and sealers should be removed with a solvent as they could inhibit the development of the “wet look” when applying TK BRIGHT SEAL WB. Rinse thoroughly and allow surface to fully dry.

A test panel mock-up should be performed prior to project start up to determine coverage rates, proper appearance and results. Apply enough TK-BRIGHT SEAL WB to satisfy the porosity of the substrate while leaving a thin film on the surface.

Steel Troweled Surface Preparation - Surface should be etched with Surecrete SCR or shot blasted to promote better adhesion. 


APPLICATION PROCEDURE
For Horizontal Surfaces: May be applied by low pressure sprayer and back rolled. It may also be applied with a roller or brush in small areas. Apply in a uniform manner and at the specified application rate, taking care to avoid lap marks. Use natural break points, such as cuts and joints as stopping points whenever possible. DO NOT OVER APPLY.

For Vertical Surfaces: For best results, apply with an airless sprayer and back roll. Apply in a uniform manner at the specified application rate, taking care to avoid lap marks. Use natural break points, such as cuts and joints as stopping points whenever possible. DO NOT OVER APPLY.


CLEAN UP
Use soap and water before the material has dried. If the material is already dry, use MEK or Xylene (methyl ethyl ketone) to remove.


MAINTENANCE
Any stains or spills should be removed as soon as possible. TKBRIGHT SEAL WB may be reapplied to areas that are worn or where spills have removed the sealer.


LIMITATIONS

  • Apply in temperatures above 50°F.
  •  Protect from freezing.
  • Do not apply to exterior horizontal surfaces that pond water as this may cause a blushing to occur.
  • Not for use on asphalt or surfaces where spillage of solvents, fuels, brake or transmission fluids are expected.
  • Avoid heavy accumulations as this can cause slippery conditions or a lifting action between coats.
See More

TK Products Bright Seal WB Premium Acrylic Concrete Sealer

Quantity must be 1 or more
Regular price
$69.95
Sale price
$69.95

This water-based acrylic wet-look sealer for decorative concrete provides color saturation and enhancement rarely found in other water-based sealers.

 

  • Dries clear with the glossy “wet look” finish sought after for decorative concrete surfaces
  • Highlights and enhances colored and decorative surfaces
  • UV stable
  • Ideal for use on interior and exterior surfaces where harsh solvent based systems cannot be tolerated
  • Use on new or existing concrete

About

TK-BRIGHT SEAL WB is an acrylic, waterborne, high solids sealer for new or existing decorative concrete. TK-BRIGHT SEAL WB brings out the “wet look” and highlights the natural pigments in the surface, all while protecting it against abrasion and damage.

TK Bright Seal WB is suitable for interior or exterior use on concrete floors, walls, columns, pavers, burnished block or exposed aggregate. Ideal for use in industrial, commercial, residential or institutional environments. 


Specs

  • Coverage: 300-500 sq.ft/gal
  • Color: Clear
  • VOC: <100 g/L
  • VOC Compliance: AIM, OTC, LADCO, CARB, CSAQMD, Canada
  • Package Qty: 1 gallon plastic bottle

Instructions

PREPARATION
TK BRIGHT SEAL WB is ready for use. Do not dilute. Surfaces must be clean, dry and free of foreign contaminants. Sweep or vacuum to remove dirt or dust, or use Surecrete SCR to clean the surface of oils, grease, stains, wax or polish. Curing compounds and sealers should be removed with a solvent as they could inhibit the development of the “wet look” when applying TK BRIGHT SEAL WB. Rinse thoroughly and allow surface to fully dry.

A test panel mock-up should be performed prior to project start up to determine coverage rates, proper appearance and results. Apply enough TK-BRIGHT SEAL WB to satisfy the porosity of the substrate while leaving a thin film on the surface.

Steel Troweled Surface Preparation - Surface should be etched with Surecrete SCR or shot blasted to promote better adhesion. 


APPLICATION PROCEDURE
For Horizontal Surfaces: May be applied by low pressure sprayer and back rolled. It may also be applied with a roller or brush in small areas. Apply in a uniform manner and at the specified application rate, taking care to avoid lap marks. Use natural break points, such as cuts and joints as stopping points whenever possible. DO NOT OVER APPLY.

For Vertical Surfaces: For best results, apply with an airless sprayer and back roll. Apply in a uniform manner at the specified application rate, taking care to avoid lap marks. Use natural break points, such as cuts and joints as stopping points whenever possible. DO NOT OVER APPLY.


CLEAN UP
Use soap and water before the material has dried. If the material is already dry, use MEK or Xylene (methyl ethyl ketone) to remove.


MAINTENANCE
Any stains or spills should be removed as soon as possible. TKBRIGHT SEAL WB may be reapplied to areas that are worn or where spills have removed the sealer.


LIMITATIONS

  • Apply in temperatures above 50°F.
  •  Protect from freezing.
  • Do not apply to exterior horizontal surfaces that pond water as this may cause a blushing to occur.
  • Not for use on asphalt or surfaces where spillage of solvents, fuels, brake or transmission fluids are expected.
  • Avoid heavy accumulations as this can cause slippery conditions or a lifting action between coats.