Concrete Coatings SuperSeal 20WB Water-Based Acrylic Sealer - Satin - 1 Gallon
About
Where Should Concrete Coatings SuperSeal 20WB Be Used?
- Odor-sensitive locations
- Schools
- Apartments
- Offices
- Restaurants
- Horizontal and vertical
- Interior and exterior
- Freshly placed and finished concrete
- Aged concrete
SuperSeal™ 20WB may be applied to many porous surfaces. We recommend you apply sealer to a small section of the substrate to ensure proper adhesion.
Important Things to Remember
- Do not use on surfaces to receive concrete overlays or additional toppings, coatings, sealers, or ceramic tile without proper surface preparation.
- Do not use in areas that require resistance to solvents.
- Do not subject to rain or water until it dries completely.
- Do not apply in highly humid conditions.
- For maximum life expectancy, routinely sweep and wash floors with appropriate cleaners and detergents.
Material
Estimator
How many square feet is your project?
NOTE: Coverages shown are based on an average coverage of 350 square feet per gallon per coat.
Specs
- Coverage: 300-400 sq. ft. /Gal
- Appearance (cured): satin
- Appearance (wet): milky liquid
- Set to Touch: 30 Minutes
- Set to Recoat: 1.5 Hours
- Set for Light Foot Traffic: 4 Hours
- Set for Normal Traffic: Overnight
- Maximum Hardness: 7 Days
How-To
- Apply a continuous, uniform film by low-pressure spray, short-nap roller, or lamb’s wool applicator. A low-pressure hand-pump sprayer is recommended for best results.
- For curing, only 1 coat is necessary. Apply evenly as soon as possible after final finishing. To seal and dust proof, 2 coats must be applied at the recommended rates. Apply the second application when all trades are completed, and the site is ready for occupancy.
- SuperSeal 20WB applied at 40 to 50° F (4 to 10° C) may retain a white appearance for extended periods, depending on temperature variations. This condition should be temporary. Warmer temperatures will allow the material to dry clear.
See More
About
Where Should Concrete Coatings SuperSeal 20WB Be Used?
- Odor-sensitive locations
- Schools
- Apartments
- Offices
- Restaurants
- Horizontal and vertical
- Interior and exterior
- Freshly placed and finished concrete
- Aged concrete
SuperSeal™ 20WB may be applied to many porous surfaces. We recommend you apply sealer to a small section of the substrate to ensure proper adhesion.
Important Things to Remember
- Do not use on surfaces to receive concrete overlays or additional toppings, coatings, sealers, or ceramic tile without proper surface preparation.
- Do not use in areas that require resistance to solvents.
- Do not subject to rain or water until it dries completely.
- Do not apply in highly humid conditions.
- For maximum life expectancy, routinely sweep and wash floors with appropriate cleaners and detergents.
Material
Estimator
How many square feet is your project?
NOTE: Coverages shown are based on an average coverage of 350 square feet per gallon per coat.
Specs
- Coverage: 300-400 sq. ft. /Gal
- Appearance (cured): satin
- Appearance (wet): milky liquid
- Set to Touch: 30 Minutes
- Set to Recoat: 1.5 Hours
- Set for Light Foot Traffic: 4 Hours
- Set for Normal Traffic: Overnight
- Maximum Hardness: 7 Days
How-To
- Apply a continuous, uniform film by low-pressure spray, short-nap roller, or lamb’s wool applicator. A low-pressure hand-pump sprayer is recommended for best results.
- For curing, only 1 coat is necessary. Apply evenly as soon as possible after final finishing. To seal and dust proof, 2 coats must be applied at the recommended rates. Apply the second application when all trades are completed, and the site is ready for occupancy.
- SuperSeal 20WB applied at 40 to 50° F (4 to 10° C) may retain a white appearance for extended periods, depending on temperature variations. This condition should be temporary. Warmer temperatures will allow the material to dry clear.
