Order $24.50 or more to qualify for FREE Shipping on eligible items. (Contiguous 48)

Surecrete ColorTec Acrylic LV Pigmented Concrete Sealer - 1 Gallon


About

SureCrete ColorTec Acrylic LV Pigmented Concrete Sealer is a single-component, 30% solids, low VOC (<400 g/l), color sealer developed for SureCrete overlays or any cement based product. Pigments are specifically formulate for UV stability, will not blush, and retain long gloss retention.

Calculator

How many square feet is your project?

NOTE: Coverages provided are based on a coverage rate of 180 square feet per gallon per coat. Your coverage may vary based on your concrete's porosity.

Coat Gallons
1 coat

Specs

  • Coverage: approx. 160-200 square feet per gallon
  • VOC Content: 400 g/l
  • Solids Content: 30%

Instructions

Surface Prep

The principles for surface preparation for ColorTec Acrylic-LV are aligned with other coating systems placed on concrete or cement based overlays, the substrate must be:

  1. Clean: The surface must be free of dust, dirt, oil, grease, paints, glues, non-acrylic sealers, curing agents, efflorescence, chemical contaminants, rust, algae, mildew, and other foreign matter that may serve as a bond breaker.
  2. Cured: Any concrete must be sufficiently cured to have complete hydration, approximately 28 days depending on temperatures & humidity, Cement based overlays typically cure sufficiently within 2-3 days.
  3. Sound: No system should be placed on concrete or cement based overlay that is flaking or spalling. If the surface is delaminating, then diamond grinding, shot blasting, or other mechanical means should be used to remove the delaminating areas.
  4. Profiled: Proper profile should follow the standard established by the International Concrete Repair Institute (ICRI) Technical Guideline no. 03732 for Concrete Surface Profile (CSP). The established profile is categorized as CSP-1. The most common means to properly profile many concrete slabs (especially exterior slabs) is through the use of a pressure washer equipped with a turbo-tip and SCR (see SCR TDS). In one step SCR profiles, cleans, and provides a measure of degreasing. Some concrete slabs that are hard troweled may require more aggressive profiling through diamond grinding or shot blasting. Customarily cement based overlays do not require profiling.

Recoats

Pigmented SBL may serve as an excellent choice to reseal or refresh an existing decorative concrete project. The surface should be cleaned with a pressure washer and SCR (see SCR TDS).

  1. Any old, loose and flaky selaer that is still present must be removed.
    • Chemically: Fast-Strip Plus, Enviro-Strip (see appropriate TDS), or other commercial stripper.
    • Mechanically: diamond grinding or shot blasting
  2. This product should only recoat an existing solvent based acrylic. Determine a substrate's unknown existing sealer by placing a paper towel saturated with xylene over a small area. Cover the towel with plastic and allow it to remain in place for 15 minutes. Solvent based acrylic may feel slippery to the touch, but water based acrylic turns into a slimy mess that can be scraped off easily.
  3. Before recoating, prepare on-site a small test area on the intended substrate to establish compatibility of solvents and avoid blistering and delamination.
  4. Recoat applications may be complete with a single coat, always evaluate surface to see if a second coat is needed. Best performance is achieved through thin coat(s).


Application

Planning

  1. Product is flammable. Interior applications, turn off all fuel burning appliances and pilot lights.
  2. Provide for ventilation so that vapors do not accumulate.
  3. Select appropriate PPE (personal protection equipment). Use of a NIOSH approved respirator may be required. Refer to SDS.

Mask all areas requiring protection.

Temperature/weather

  1. Avoid application on extremely cold or hot days or during wet, foggy weather.
  2. Apply with ambient and surface temperatures ranging above 50°F (10°C) and below 90°F (32°C) and that will remain within ranges for at least 24 hours following application.
  3. Do not apply outside if precipitation is forecast within 24 hours of application.
  4. Substrate must be dry throughout all steps.

Mixing
Mechanically mix with "Jiffy" style mixer blade for 3 minutes at medium speed for complete dispersal of pigments. Use caution not to entrain air during mixing.

First Coat

  • Rolling
    1. Utilize a bucket grid to apply in a thin film.
    2. Roller covers require a solvent resistant core.
    3. The correct nap size varies due to texture. For example 3/4" is recommended for heavy textured patterns, while 1/4" mohair is recommended for very smooth surfaces.
    4. Do not allow puddling.
    5. Exercise care to eliminate roller tracks through back rolling.
  • Airless Spraying
    1. Airless sprayer should be capable of a minimum .5 gpm discharge.
    2. Tip size should be approximately .015" - .019" with 65° fan.
    3. For horizontal surface utilize an 8" - 10" extension.
    4. Maintain a wet edge between passes.
  • Pump-Up Sprayer
    1. Select solvent resistant sprayer.
    2. Select fan or cone tip as preferred that can pass 30% solids product.
    3. Have sufficient tips on hand to allow clean-up that will not interrupt application.
    4. If necessary, backroll sprayed area to lay product flat.

When first coat is able to be walked on, it may receive a second coat. While many applications are complete with a single coat, always evaluate surface to see if a second coat is needed. For single coat system: Allow 24 hours cure time prior to foot traffic. Allow 72 hours cure time prior to vehicular traffic.

Second Coat

  • Applies identical to first coat.
  • Allow 24 hours cure time prior to foot traffic.
  • Allow 72 hours cure time prior to vehicular traffic.


Slip Resistance

Two recognized US agencies have issued directives on minimum coefficient of friction, OSHA (Occupational Safety and Health Administration) and Department of Justice through the ADA (Americans with Disabilities Act). ADA is the more stringent of the two. ADA directs that accessible walkways have a minimum coefficient of friction of 0.6. Ramps have been directed to be 0.8. The applicator assumes the responsibility to meet these standards. Areas that may become wet, oily, or greasy require special attention. Refer to SureGrip (Additive) TDS and its accompanying coefficient of friction table.


Suitability Sample

Due to condition specific sites, always prepare an adequate number of test areas. Wear protection system and aesthetic suitability for products' intended use should be included. On site sample approval is especially critical on substantial, heavy traffic situation, custom coloration, and desired hide.


Clean Up

Before ColorTec Acrylic-LV dries; spills and tools can be cleaned up with a solvent such as xylene or acetone.


Disposal

Contact your local government household hazardous waste coordinator for information on disposal of unused product.


Limitations

  • For use by trained professionals that have read the complete SDS.
  • Product performs best upon a concrete slab that has no ponding of standing water.
  • When masking use caution while taping to a floor that is not completely cured, especially at edges, as delamination may occur.
  • Protect from metal wheel traffic and some furniture where point of contact may be damaging.
  • Chemicals used in tire manufacturing may be detrimental to all sealers from vehicular parking.
See More

Surecrete ColorTec Acrylic LV Pigmented Concrete Sealer - 1 Gallon

Quantity must be 1 or more
Color
Regular price
$82.95
Sale price
$82.95

Save time between coats  on your next outdoor project. Enjoy customized pigments that are formulated for UV stability, will not blush or delaminate, and retain long gloss retention.

  • Enhances beauty
  • Improves stain and abrasion resistance
  • Vapor permeable, yet reduces penetration of fluids

Attention: Material is considered hazmat, and cannot be shipped air.

About

SureCrete ColorTec Acrylic LV Pigmented Concrete Sealer is a single-component, 30% solids, low VOC (<400 g/l), color sealer developed for SureCrete overlays or any cement based product. Pigments are specifically formulate for UV stability, will not blush, and retain long gloss retention.

Calculator

How many square feet is your project?

NOTE: Coverages provided are based on a coverage rate of 180 square feet per gallon per coat. Your coverage may vary based on your concrete's porosity.

Coat Gallons
1 coat

Specs

  • Coverage: approx. 160-200 square feet per gallon
  • VOC Content: 400 g/l
  • Solids Content: 30%

Instructions

Surface Prep

The principles for surface preparation for ColorTec Acrylic-LV are aligned with other coating systems placed on concrete or cement based overlays, the substrate must be:

  1. Clean: The surface must be free of dust, dirt, oil, grease, paints, glues, non-acrylic sealers, curing agents, efflorescence, chemical contaminants, rust, algae, mildew, and other foreign matter that may serve as a bond breaker.
  2. Cured: Any concrete must be sufficiently cured to have complete hydration, approximately 28 days depending on temperatures & humidity, Cement based overlays typically cure sufficiently within 2-3 days.
  3. Sound: No system should be placed on concrete or cement based overlay that is flaking or spalling. If the surface is delaminating, then diamond grinding, shot blasting, or other mechanical means should be used to remove the delaminating areas.
  4. Profiled: Proper profile should follow the standard established by the International Concrete Repair Institute (ICRI) Technical Guideline no. 03732 for Concrete Surface Profile (CSP). The established profile is categorized as CSP-1. The most common means to properly profile many concrete slabs (especially exterior slabs) is through the use of a pressure washer equipped with a turbo-tip and SCR (see SCR TDS). In one step SCR profiles, cleans, and provides a measure of degreasing. Some concrete slabs that are hard troweled may require more aggressive profiling through diamond grinding or shot blasting. Customarily cement based overlays do not require profiling.

Recoats

Pigmented SBL may serve as an excellent choice to reseal or refresh an existing decorative concrete project. The surface should be cleaned with a pressure washer and SCR (see SCR TDS).

  1. Any old, loose and flaky selaer that is still present must be removed.
    • Chemically: Fast-Strip Plus, Enviro-Strip (see appropriate TDS), or other commercial stripper.
    • Mechanically: diamond grinding or shot blasting
  2. This product should only recoat an existing solvent based acrylic. Determine a substrate's unknown existing sealer by placing a paper towel saturated with xylene over a small area. Cover the towel with plastic and allow it to remain in place for 15 minutes. Solvent based acrylic may feel slippery to the touch, but water based acrylic turns into a slimy mess that can be scraped off easily.
  3. Before recoating, prepare on-site a small test area on the intended substrate to establish compatibility of solvents and avoid blistering and delamination.
  4. Recoat applications may be complete with a single coat, always evaluate surface to see if a second coat is needed. Best performance is achieved through thin coat(s).


Application

Planning

  1. Product is flammable. Interior applications, turn off all fuel burning appliances and pilot lights.
  2. Provide for ventilation so that vapors do not accumulate.
  3. Select appropriate PPE (personal protection equipment). Use of a NIOSH approved respirator may be required. Refer to SDS.

Mask all areas requiring protection.

Temperature/weather

  1. Avoid application on extremely cold or hot days or during wet, foggy weather.
  2. Apply with ambient and surface temperatures ranging above 50°F (10°C) and below 90°F (32°C) and that will remain within ranges for at least 24 hours following application.
  3. Do not apply outside if precipitation is forecast within 24 hours of application.
  4. Substrate must be dry throughout all steps.

Mixing
Mechanically mix with "Jiffy" style mixer blade for 3 minutes at medium speed for complete dispersal of pigments. Use caution not to entrain air during mixing.

First Coat

  • Rolling
    1. Utilize a bucket grid to apply in a thin film.
    2. Roller covers require a solvent resistant core.
    3. The correct nap size varies due to texture. For example 3/4" is recommended for heavy textured patterns, while 1/4" mohair is recommended for very smooth surfaces.
    4. Do not allow puddling.
    5. Exercise care to eliminate roller tracks through back rolling.
  • Airless Spraying
    1. Airless sprayer should be capable of a minimum .5 gpm discharge.
    2. Tip size should be approximately .015" - .019" with 65° fan.
    3. For horizontal surface utilize an 8" - 10" extension.
    4. Maintain a wet edge between passes.
  • Pump-Up Sprayer
    1. Select solvent resistant sprayer.
    2. Select fan or cone tip as preferred that can pass 30% solids product.
    3. Have sufficient tips on hand to allow clean-up that will not interrupt application.
    4. If necessary, backroll sprayed area to lay product flat.

When first coat is able to be walked on, it may receive a second coat. While many applications are complete with a single coat, always evaluate surface to see if a second coat is needed. For single coat system: Allow 24 hours cure time prior to foot traffic. Allow 72 hours cure time prior to vehicular traffic.

Second Coat

  • Applies identical to first coat.
  • Allow 24 hours cure time prior to foot traffic.
  • Allow 72 hours cure time prior to vehicular traffic.


Slip Resistance

Two recognized US agencies have issued directives on minimum coefficient of friction, OSHA (Occupational Safety and Health Administration) and Department of Justice through the ADA (Americans with Disabilities Act). ADA is the more stringent of the two. ADA directs that accessible walkways have a minimum coefficient of friction of 0.6. Ramps have been directed to be 0.8. The applicator assumes the responsibility to meet these standards. Areas that may become wet, oily, or greasy require special attention. Refer to SureGrip (Additive) TDS and its accompanying coefficient of friction table.


Suitability Sample

Due to condition specific sites, always prepare an adequate number of test areas. Wear protection system and aesthetic suitability for products' intended use should be included. On site sample approval is especially critical on substantial, heavy traffic situation, custom coloration, and desired hide.


Clean Up

Before ColorTec Acrylic-LV dries; spills and tools can be cleaned up with a solvent such as xylene or acetone.


Disposal

Contact your local government household hazardous waste coordinator for information on disposal of unused product.


Limitations

  • For use by trained professionals that have read the complete SDS.
  • Product performs best upon a concrete slab that has no ponding of standing water.
  • When masking use caution while taping to a floor that is not completely cured, especially at edges, as delamination may occur.
  • Protect from metal wheel traffic and some furniture where point of contact may be damaging.
  • Chemicals used in tire manufacturing may be detrimental to all sealers from vehicular parking.