FREE SHIPPING on eligible items when you order $24.50 or more! (48 Contiguous States)

SureCrete RESIST Epoxy (10-Gallon)

SureCrete RESIST Epoxy Sand Overlay System with RESIST Armorstone Wear Aggregate and Eco-Stain accents

SureCrete RESIST Epoxy (10-Gallon)

Stair tread close-up with RESIST Armorstone Wear Aggregate

SureCrete RESIST Epoxy (10-Gallon)
SureCrete RESIST Epoxy (10-Gallon)

About

The SureCrete RESIST Epoxy Sand Overlay System

SureCrete’s RESIST is a 100% active, low modulus, two-component epoxy overlay system that when combined with a kiln-dried, properly sourced wear surface aggregate, produces a reliant overlay with benefits not found in traditional concrete overlays.

  • Tenacious bond strength creating a durable, slip-resistant overlay system
  • Superior resiliency and impact / wear resistance
  • Bonds directly with the surface for exceptional chemical resistance and waterproofing
  • Non-shrink and flexible enough to withstand slight movement and extreme temperature changes
  • Cost effective with a 20 year history of high performance, repairs in the most extreme conditions
  • Easy to use 1:1 mixing ratio
  • Complete system that provides compatible products for crack repair, surface defects as well as a non-yellowing, color enhancing, protective top coat

See all the products in the SureCrete RESIST Epoxy Sand Overlay System

Specs

TECHNICAL DATA INFORMATION
CoverageBase Coat 150 sq ft per gallon base coat
Second Coat  75 - 100 sq ft per gallon second coat with snd broadcast
Coverage rates are provided as a guideline only. Many factors including surface texture, porosity and weather conditions will determine actual coverage rates.
Gel Time at 75°25-35 Minutes
Viscosity400-600 cps
A.I.M. CategoryConcrete Protective Coating Maximum VOC 400 g/l
Applicable Standards
  • ASTM C-881, Type III, Grade 1, Class B and C
  • ASTM D-695 Compressive Modulus
  • ASTM D-638 Tensile Strength and Elongation
  • AASHTO M-235 Type II and III, Grade 1, Class B,C and D
Testing DataASTM C882 – SLANT SHEAR BOND STRENGTH 
  • 2 days - 890 psi 
  • 14 days - 1,395 psi 
ASTM D638 – TENSILE STRENGTH 
  • Tensile Strength at 7 days - 1,744 psi 
  • Tensile Elongation at 7 days -  1.6% 
  • Tensile Modulus at 7 days - 6.6 x 105 psi 
ASTM D695 – COMPRESSIVE YIELD STRENGTH 
  • 1 day - 5,088 psi 
  • 3 days - 5,697 psi 
  • 7 days - 5,955 psi 
  • 14 days - 6,128 psi 
  • 28 days – 6144 psi

    Instructions

    Preparation

    1. A proper inspection of the concrete is required to check for structural deficiencies, and any deteriorated areas should be promptly marked and removed.
    2. Repair delamination, potholes and cracks 
    3. The entire surface should be shot blasted or ground to a CSP #2 to #3 or depth that ensures that all deteriorated and contaminated concrete (oil, dirt, rubber, paint carbonation, laitance, weak surface mortar, etc) is removed.
    4. Remove any remaining dust with compressed air, using a properly maintained and filtered compressor that will not spray oil or moisture onto the deck.
    5. If you pressure wash make sure concrete is fully dry. The overlay should be applied to the surface within 24 hours of cleaning.
    6. For applications exposed to heavy wear and/or in the case of concrete slabs that are soft or extremely porous, a base coat of RESIST Epoxy will be required. The base coat, applied at a rate of 200 sq’ per gallon, should be treated with a full broadcast of RESIST approved wear surface aggregate and allowed to cure prior to installing the main RESIST application.
    7. RESIST Sand Finish Overlay may be used at a range of temperatures, however the user should be aware that temperature plays a role in the pot life and cure times of this product. Higher temperatures will result in shorter pot life and cure times, while lower temperatures will result in longer pot life and cure times.

    Mixing

    1. Mixing ratio for the two components is 1:1 by volume (not weight). 
    2. Components “A” and “B” are supplied in separate containers and should be combined using a paddle mixer (powered by a low speed electric drill) or a proportioning pump for 3-5 minutes. 
    3. RESIST SAND FINISH OVERLAY does not contain volatile solvents and solvents should not be added to this product. 
    4. When using the Armorstone aggregate, you will simply Part A and Part B as described above. 
      • When using the Goldmine aggregate, you will need to add the Antique White 1 Quart Universal Tint Paste per every 2 Gallons of mixed material (1-Gallon Part A & 1-Gallon Part B.). Best practice is to introduce the 1 quart of colorant into the Part A (1 Gallon, mix thoroughly) and then introduce Part B into that colored Part A. 
      • When using the Silver Fox aggregate, you will need to add the Silver Gray 1 Quart Universal Tint Paste per every 2 Gallons of mixed material (1-Gallon Part A & 1-Gallon Part B.). Best practice is to introduce the 1 quart of colorant into the Part A (1 Gallon, mix thoroughly) and then introduce Part B into that colored Part A. 

    Application

    This product should be used immediately upon mixing as this will increase its available working time. 

    1. The mixed epoxy should be poured onto the surface and spread at the proper application rate using a notched squeegee (a notched squeegee will facilitate proper mil thickness). 
    2. Back roll with a 3/8 to 1/2 inch roller to ensure all lines are evened out. 
    3. Immediately follow this with a broadcast of sands over the epoxy at a rate sufficient to completely cover the epoxy. If need be, recoat with sand to make sure epoxy is covered.

    Pro Tips

    • Stage work stations. 
    • Load sands in easy scoopable trays for broadcasting. 
    • Dispense contents from mixing bucket immediately to avoid the epoxy from setting rapidly in the bucket.
    See More

    SureCrete RESIST Epoxy (10-Gallon)

    Quantity must be 1 or more
    Regular price
    $1,079.95
    Sale price
    $1,079.95
    RESIST Epoxy is a 100% solids, solvent-free, two-component epoxy system. Formulated to seal, protect, and lengthen the life of concrete and parking structures, RESIST Sand Finish Overlay also provides exceptional skid resistance with a top layer of specially selected aggregate available in three colors; Armorstone, Goldmine, and Silver Fox.
    • Excellent bond strength for a durable, yet flexible coating that is resistant to moisture
    • Superior resiliency and impact resistance
    • Bonds directly with the surface for exceptional chemical and water resistance
    • Non-shrink and flexible enough to withstand slight movement and extreme temperature changes
    • Provides skid resistance with a top-layer of specially selected aggregate (purchased separately)
    • Easy to use 1:1 mixing ratio
    • Includes 5 Gallons Part A and 5 Gallons Part B
    • Coverage: 150 – 200 sq ft per gallon

    Attention: Material is considered hazmat, and cannot be shipped air.

    About

    The SureCrete RESIST Epoxy Sand Overlay System

    SureCrete’s RESIST is a 100% active, low modulus, two-component epoxy overlay system that when combined with a kiln-dried, properly sourced wear surface aggregate, produces a reliant overlay with benefits not found in traditional concrete overlays.

    • Tenacious bond strength creating a durable, slip-resistant overlay system
    • Superior resiliency and impact / wear resistance
    • Bonds directly with the surface for exceptional chemical resistance and waterproofing
    • Non-shrink and flexible enough to withstand slight movement and extreme temperature changes
    • Cost effective with a 20 year history of high performance, repairs in the most extreme conditions
    • Easy to use 1:1 mixing ratio
    • Complete system that provides compatible products for crack repair, surface defects as well as a non-yellowing, color enhancing, protective top coat

    See all the products in the SureCrete RESIST Epoxy Sand Overlay System

    Specs

    TECHNICAL DATA INFORMATION
    CoverageBase Coat 150 sq ft per gallon base coat
    Second Coat  75 - 100 sq ft per gallon second coat with snd broadcast
    Coverage rates are provided as a guideline only. Many factors including surface texture, porosity and weather conditions will determine actual coverage rates.
    Gel Time at 75°25-35 Minutes
    Viscosity400-600 cps
    A.I.M. CategoryConcrete Protective Coating Maximum VOC 400 g/l
    Applicable Standards
    • ASTM C-881, Type III, Grade 1, Class B and C
    • ASTM D-695 Compressive Modulus
    • ASTM D-638 Tensile Strength and Elongation
    • AASHTO M-235 Type II and III, Grade 1, Class B,C and D
    Testing DataASTM C882 – SLANT SHEAR BOND STRENGTH 
    • 2 days - 890 psi 
    • 14 days - 1,395 psi 
    ASTM D638 – TENSILE STRENGTH 
    • Tensile Strength at 7 days - 1,744 psi 
    • Tensile Elongation at 7 days -  1.6% 
    • Tensile Modulus at 7 days - 6.6 x 105 psi 
    ASTM D695 – COMPRESSIVE YIELD STRENGTH 
    • 1 day - 5,088 psi 
    • 3 days - 5,697 psi 
    • 7 days - 5,955 psi 
    • 14 days - 6,128 psi 
    • 28 days – 6144 psi

      Instructions

      Preparation

      1. A proper inspection of the concrete is required to check for structural deficiencies, and any deteriorated areas should be promptly marked and removed.
      2. Repair delamination, potholes and cracks 
      3. The entire surface should be shot blasted or ground to a CSP #2 to #3 or depth that ensures that all deteriorated and contaminated concrete (oil, dirt, rubber, paint carbonation, laitance, weak surface mortar, etc) is removed.
      4. Remove any remaining dust with compressed air, using a properly maintained and filtered compressor that will not spray oil or moisture onto the deck.
      5. If you pressure wash make sure concrete is fully dry. The overlay should be applied to the surface within 24 hours of cleaning.
      6. For applications exposed to heavy wear and/or in the case of concrete slabs that are soft or extremely porous, a base coat of RESIST Epoxy will be required. The base coat, applied at a rate of 200 sq’ per gallon, should be treated with a full broadcast of RESIST approved wear surface aggregate and allowed to cure prior to installing the main RESIST application.
      7. RESIST Sand Finish Overlay may be used at a range of temperatures, however the user should be aware that temperature plays a role in the pot life and cure times of this product. Higher temperatures will result in shorter pot life and cure times, while lower temperatures will result in longer pot life and cure times.

      Mixing

      1. Mixing ratio for the two components is 1:1 by volume (not weight). 
      2. Components “A” and “B” are supplied in separate containers and should be combined using a paddle mixer (powered by a low speed electric drill) or a proportioning pump for 3-5 minutes. 
      3. RESIST SAND FINISH OVERLAY does not contain volatile solvents and solvents should not be added to this product. 
      4. When using the Armorstone aggregate, you will simply Part A and Part B as described above. 
        • When using the Goldmine aggregate, you will need to add the Antique White 1 Quart Universal Tint Paste per every 2 Gallons of mixed material (1-Gallon Part A & 1-Gallon Part B.). Best practice is to introduce the 1 quart of colorant into the Part A (1 Gallon, mix thoroughly) and then introduce Part B into that colored Part A. 
        • When using the Silver Fox aggregate, you will need to add the Silver Gray 1 Quart Universal Tint Paste per every 2 Gallons of mixed material (1-Gallon Part A & 1-Gallon Part B.). Best practice is to introduce the 1 quart of colorant into the Part A (1 Gallon, mix thoroughly) and then introduce Part B into that colored Part A. 

      Application

      This product should be used immediately upon mixing as this will increase its available working time. 

      1. The mixed epoxy should be poured onto the surface and spread at the proper application rate using a notched squeegee (a notched squeegee will facilitate proper mil thickness). 
      2. Back roll with a 3/8 to 1/2 inch roller to ensure all lines are evened out. 
      3. Immediately follow this with a broadcast of sands over the epoxy at a rate sufficient to completely cover the epoxy. If need be, recoat with sand to make sure epoxy is covered.

      Pro Tips

      • Stage work stations. 
      • Load sands in easy scoopable trays for broadcasting. 
      • Dispense contents from mixing bucket immediately to avoid the epoxy from setting rapidly in the bucket.